How To Clean Dyson Vacuum Head?

The Dyson Vacuum head gets stuck on the bottom while cleaning, so you need a proper guide to clean it.

Vacuum cleaners can help you keep your living space clean, the Dyson is a leading and stylish vacuum cleaner brand.

Their vacuums are strong and easy to use, however, the vacuum head can get dusty over time and needs to be cleaned.

It was observed that the average American family had around 100 germs and bacteria, a bit dusty!

It’s not just the dust that can build up on your vacuum head.

This implies that you should clean your vacuum head daily to ensure that it is performing effectively and not just pulling dirt and debris.

Since there are so many delicate parts on a Dyson vacuum head, cleaning may be difficult hence you must thoroughly read this article.

Because I have provided a step-by-step procedure to clean the Dyson vacuum head.

I’ve also included some necessary instructions that you should read before doing something else with your Dyson vacuum head.

So, let’s begin!

How To Clean Dyson Vacuum Head

Instructions to Clean the Dyson Vacuum Head:

Dyson Vacuum Cleaner is a really good investment for your home, they have strong suction intended to clean many areas.

While cleansing a vacuum head, there are some things to remember as follows:

  • Before cleaning the vacuum cleaner’s head, disconnect it from the power socket.
  • Gently wipe off any dust and debris on the vacuum head using a soft cloth or brush.
  • Using strong chemicals or cleansers on the head can cause injury.
  • If the vacuum head is dirty, rinse it in warm water with a little detergent.
  • Before re-using the vacuum, rinse and dry the head thoroughly.
  • Use the vacuum without the head to avoid causing damage to the equipment.

By following these easy instructions, you can maintain your Dyson vacuum head in perfect condition for several years.

How To Clean Dyson Vacuum Heads Step by Step:

1. Disconnect your vacuum cleaner from the wall and turn it off:

Disconnect your vacuum cleaner from the wall and turn it off

Vacuum cleaner heads can get stuck in dust and dirt and if you have just used them, it can be very hot.

To avoid damage, always unplug your vacuum and switch it off before you begin cleaning.

Typically, a switch on the main body of the vacuum can be used to close the suction head.

 If your vacuum has a wire cover, you may need to turn it off using a switch on the cable cover.

2. Take out the dustbin and put it in the trash:

Take out the dustbin and put it in the trash

The trashcan is a component of the vacuum cleaner that collects dirt and debris.

It is usually found in front of or on top of a vacuum.

Take the trash out by pressing the eject button, then pour the mixture into the garbage.

It can be seen on the side or back of different designs, so consult your owner’s handbook to determine where it is located on your device.

 If you have problems with your machine, please contact the Dyson Helpline.

3. Remove the screw holding the vacuum head:

Remove the screw holding the vacuum head

Remove the screw connecting the vacuum head.

Usually, both sides have two screws and using a screwdriver, remove these screws.

 Note where the screws go because you will need to replace them later.

If your vacuum head is held by a holding tab instead of a screw, just press the tab to remove it.

I realize that it is new for you, but it will make things much easier in the longer term.

4. Gently remove the vacuum head from the main unit:

Gently remove the vacuum head from the main unit

The vacuum head is a component of a vacuum cleaner that touches the flooring or carpet.

It is in charge of vacuuming dirt, dust, and detritus, so after disconnecting your Dyson vacuum cleaner’s screws and trash.

Now, you must remove the vacuum head & take it from above and draw it for yourself.

You can also read the guidebook for further instructions on vacuum head removal.

5. Use a brush to remove any dirt from the bristles:

Use a brush to remove any dirt from the bristles

Vacuum head bristles are used to help clean the flooring.

Based on the kind of Dyson vacuum, they are made up of various components.

Clean away any dirt that has been caught within the bristles with a brush.

Remove excess fur or debris trapped in bristles.

Yet, brushes with metallic bristles must be avoided since they might harm the vacuum head.

It may also include cleaning tools.

6. Clean the entire surface of the vacuum head:

Clean the entire surface of the vacuum head

A damp cloth is a cloth that is lightly soaked in water or another liquid.

Using a moist cloth, properly clean the whole area of the vacuum head.

This comprises the vacuum head’s top, bottom, and corners.

Wash away any dirt, grit, or particles from the vacuum head’s surface because the Dyson vacuum head is composed of plastic.

It is critical not to use harsh chemicals or cleaners on its surface.

7. Remove the filter and wash in hot, soapy water:

Remove the filter and wash in hot, soapy water

A vacuum cleaner filter is a device that filters airborne particles when vacuumed in a machine.

This improves the suction power of the vacuum, it prevents dirt and dust from re-exploding in the room.

You must now remove the filter from your Dyson vacuum cleaner.

The majority of Dyson vacuum cleaners include two filters: one for the engine and one for the suction.

Keep in mind what each filter is before you start.

8. Shake off any excess water and air dry:

Shake off any excess water and air dry

After extracting the filters, brush out any leftover water and air dry them.

It is important not to return the filter to a vacuum until it is completely dry, as this can damage the machine.

You may also cleanse the interior of the vacuum head with a gentle brush.

Alternatively, if your hose is removable, you can remove it and rinse it with warm, soapy water.

However, it is better to consult the user’s handbook first, as certain vacuum cleaners do not have separate hoses.

9. Replace the screws and reconnect the vacuum head to the main unit:

Replace the screws and reconnect the vacuum head to the main unit

The body of the device is the primary unit of a vacuum cleaner; the engine, filter, and trash are all located here.

The vacuum head is the part of the equipment that collects dirt and particles often connected to the main unit through a hose or line.

 To clean the vacuum head, you must first remove it from the main system, then after finishing the preceding tasks.

 All of the screws and the vacuum head must be reattached to the main unit.

10. Also replace the dustbin and reconnect the vacuum cleaner:

Replace the dustbin and reconnect the vacuum cleaner

The vacuum cleaner’s container catches absorbed dirt and debris.

Press it back into position until it clicks to reconnect, then connect the power wire to the outlet.

Check that the cord is fully plugged into the socket.

A loose connection can reduce the power of a vacuum, however, your vacuum should be on and ready to go.

Your vacuum cleaner is now set to use!

Other parts that should be cleaned with Dyson Vacuum Head:

A cleaning system is included in the vacuum cleaner, however, it is integrated with many mechanical moving elements just like any other device.

 To keep equipment running efficiently, it needs to be cleaned and maintained regularly.

The following are the essential components of a vacuum cleaner that should be cleaned regularly:

Brush roll:

The brush roll flooring is the charge of agitation to release dirt and debris.

This vacuum also helps in the movement of dirt and particles towards the head.

To ensure that the brush roll can continue its work efficiently, it should be wiped regularly.

Hose:

The hose transports dirt and debris from the vacuum head to the garbage container.

If the hose is blocked, the vacuum will not work properly.

To keep the hose free of obstructions, wash it regularly.

Filter:

The filter is the charge of collecting dirt and dust particles that are sucked up by the vacuum.

To keep the filter from getting blocked and ineffective, it should be maintained regularly.

How often should you clean the Dyson vacuum head?

To maintain the suction force and prevent working components from contamination and breakage, keep your vacuum head clean.

  • Depending on the frequent usage, you must clean the vacuum head every 2 or 3 months.
  • If your vacuum does not accumulate as much debris as before or the head appears to be stuck, it needs to be cleaned.
  • You may need to wash more frequently if you have pets or live in a dusty environment, so if you live in a dirty area or have pets, you should clean your vacuum head every one or two months.
  • As these conditions apply to you, you can easily clean it every 3 months and get rid of it.
Also read: Difference Between Vacuum Cleaner and Carpet Steamer

FAQ- How to Clean Dyson Vacuum Heads:

Q1. How can I get the dirt out of a vacuum head?

Remove the three screws that hold the soleplate in place. You’ll then be able to see the garbage. Simply remove it and dump it. Just take it out and empty it.

Q2. What can I do if hair becomes intertwined in the vacuum head?

If your hair is long, it will inevitably get stuck in the beater bar of your vacuum cleaner’s head.
First, remove the beater bar and then carefully remove the hair wrapped around it.

Q3: How long does it take to clean a Dyson vacuum head?

The kind of Dyson vacuum you have typically determined this. If you have a wireless model, this may take a little longer. However, it takes an average of 20-30 minutes to clean the vacuum head.

Also read: Single-Stage vs Two-Stage Snow Blower

Conclusion:

Cleaning and maintaining your vacuum cleaner on a routine basis are important to maintaining its functioning properly.

The brush roll, hose, and filter are the major components that must be cleaned daily.

Depending on how to use it, you should wipe the vacuum head every one-and three months.

Hello & welcome to Homeprettify! I'm Pooja and I have a passion for all things design, decor, and renovation. I am a serial renovator, currently working as Civil Engineer. Look around, leave a comment, and don't forget to subscribe to my emails so you don't miss out!

Leave a Comment